Fireye M-Series II Amplifier Modules. The Fireye MART1, MART3, MART1T, MAUV1, MAUV3

[{"filename":"C-4002-M-Series_II_Amplifier_Modules_MART1_MART3_MART1T_MAUV1_MAUV3_MAUV1T_English_2015-04-28.pdf","text":"®\n\n C-4002\n APRIL 28, 2015\n\n\n\n\n MART1, MART3,\n MART1T, MAUV1,\n MAUV3 and MAUV1T\n AMPLIFIER MODULES\n FOR USE WITH THE FIREYE MODULAR\n M-SERIES II CONTROL\n\n\n\n\n APPROVED\n\n\n\n\nDESCRIPTION\n The Fireye MART1, MART3, MART1T, MAUV1, MAUV3 and MAUV1T are Amplifier Modules\n used with the Fireye Modular M-SERIES II control. These amplifier modules provide flame scan-\n ning capabilities using any of the Fireye standard ultraviolet scanners (self-check scanners not appli-\n cable) and flame rods. The Flame Failure Response Time (F.F.R.T.) of the control is determined by\n the selection of the amplifier module (see Ordering Information). Test jacks are provided on the\n amplifier modules to permit flame signal measurement during operation.\n After scanner selection, the proper amplifier module must be used in the Modular M-SERIES II\n chassis (see Ordering Information). The amplifier module incorporates a plug-in design for ease of\n installation.\n The programmer module determines the operational characteristics of the control (e.g. relight, purge\n timing, etc.).\n For proper and safe application of this product, you must refer to bulletins C-4000 or C-4000E for a\n detailed description of the operation of the Modular M-SERIES II control, including installation\n instructions, operating sequences for the programmer modules, etc. Also follow the scanner installa-\n tion and wiring instructions found in bulletins C-4000 or C-4000E for proper flame scanning opera-\n tion.\n\n\n\n\n WARNING: Selection of this control for a particular application should be made by a compe-\n tent professional, licensed by a state or other government agency. Inappropriate application\n of this product could result in an unsafe condition hazardous to life and property. Installation\n should not be considered complete until pilot turndown and other appropriate performance\n tests have been successfully completed.\n\n\n\n\n 1\n\f \n\n\n\n\nORDERING INFORMATION\nFlame Amplifier Selection:\n\n P/N DESCRIPTION USE WITH SCANNER\n MAUV1 UV amplifier, 2-4 second F.F.R.T. UV1A, UV2, UV8A, 45UV3-1050\n MAUV3 UV amplifier, 3 second F.F.R.T. UV1A, UV2, UV8A, 45UV3-1050\n MAUV1T UV amplifier, .8 second F.F.R.T. UV1A, UV2, UV8A, 45UV3-1050\n MART1 Flame rectification amplifier 2-4 second F.F.R.T. 69ND1\n MART3 Flame rectification amplifier, 3 second F.F.R.T. 69ND1\n MART1T Flame rectification amplifier .8 second F.F.R.T. 69ND1\n\n\nFLAME SCANNER SELECTION\n\n\n\n\n 48PT2-9003\n\n\n\n\n UV SCANNERS:\n UV1A3 1/2” NPT connector, 3 ft. (914 mm) TC-ER cable\n UV1A6 1/2” NPT connector, 6 ft. (1828 mm) TC-ER cable\n UV2 3/8” NPT connector, 3 ft. (914 mm) TC-ER cable\n UV8A 1/2” NPT 90 degree angle head, 6 ft. (1828 mm) unshielded leads\n UV90-3, 6, 9 90 degree lateral view, 3 ft. (914 mm), 6 ft. (1828 mm), 9 ft. (2742 mm)\n flex conduit\n 45UV3-1050 3/4” sleeve/set screw mount\n\n\n\n FLAME DETECTORS:\n 69ND1-1000K4 12 inch flame rod, 1/2” NPT connector\n 69ND1-1000K6 18 inch flame rod, 1/2” NPT connector\n 69ND1-1000K8 24 Inch flame rod, 1/2” NPT connector\n\n\n\n\n2\n\f ®\n\n\n\n\nAPPROVALS\n AGENCY APPROVALS\n ULc FM AGA EN298\n MAUV1 ✓ ✓ ✓\n MAUV3 ✓\n MAUV1T ✓ ✓ ✓ ✓\n MART1 ✓ ✓ ✓\n MART3 ✓\n MART1T ✓ ✓ ✓ ✓\n Underwriters Laboratories Inc.: Listed Guide MCCZ — File MP 1537\n Underwriters Laboratories Inc.: Recognized Components Guide MCCZ2 File MP1537\n American Gas Association\n Factory Mutual\n EN298\n ANS Z21.20 Automatic Ignition Systems.\n Remove power from the control and remove the control from its wiring base before\n proceeding.\n\n\n\nINSTALLATION\n The amplifier modules are used with the Fireye Modular M-SERIES II Base Chassis (P/N MC120,\n MC120E, MC120P, MC120R, MC120RE for 120VAC, P/N MC230, MC230R for 240VAC). They\n are installed in the chassis by grabbing hold of the amplifier module by the edges of its printed cir-\n cuit board, aligning the module with the guide slots on the opening in the middle of the chassis, and\n inserting the module into the pin connectors.\n The amplifier modules are designed to fit in the proper slot only. DO NOT FORCE THEM.\n\n\n\n\nNOTICE\n When Fireye products are combined with equipment manufactured by others and/or integrated into\n systems designed or manufactured by others, the Fireye warranty, as stated it its General Terms and\n Conditions of Sale, pertains only to the Fireye products and not to any other equipment or to the\n combined system or its overall performance.\n\n 3\n\f \n\n\n\n\nWARRANTIES\n FIREYE guarantees for one year from the date of installation or 18 months from date of manufacture of\n its products to replace, or, at its option, to repair any product or part thereof (except lamps, electronic\n tubes and photocells) which is found defective in material or workmanship or which otherwise fails to\n conform to the description of the product on the face of its sales order. THE FOREGOING IS IN\n LIEU OF ALL OTHER WARRANTIES AND FIREYE MAKES NO WARRANTY OF MER-\n CHANTABILITY OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED. Except as specifi-\n cally stated in these general terms and conditions of sale, remedies with respect to any product or part\n number manufactured or sold by Fireye shall be limited exclusively to the right to replacement or repair\n as above provided. In no event shall Fireye be liable for consequential or special damages of any nature\n that may arise in connection with such product or part.\n\n\n\n\n FIREYE C-4002\n 3 Manchester Road APRIL 28, 2015\n Derry, New Hampshire 03038 USA Supersedes February 25, 2015\n www.fireye.com\n\n\n\n 4"}]