Elektrogas NC automatic reset fast opening fast closing

[{"filename":"VMR_en.pdf","text":"VMR\n VMR 60\n VMR OTN\n Safety solenoid valves for gas\n Fast opening and fast closing type\n DN8 … DN150\n\n\n\n\ndelta-elektrogas.com EE161 -0124\n\f ELEKTROGAS – Technical Sheet EE161 - 0124\n\n\n\nVMR\nVMR 60\nVMR OTN\nSafety solenoid valves for gas\nFast opening and fast closing type\n\nContents\n Description ………………………………………….. 2\n Features …………………………………………….. 2\n Functioning and application ………………………. 3\n Technical specifications …………………………… 4\n Gas flow chart (pressure drop) …………………… 6\n Ordering information ………………………………. 8\n Special versions and options ……...……………… 9\n Design, installation and servicing ........................ 10\n Standards and approvals …………………………. 11\n\n\nDescription The VMR type valve is a fast opening single-stage solenoid valve, normally closed (open when\n energized). This type of device is suitable for air or gas blocking and releasing controls, required\n in gas power burners, atmospheric gas boilers, industrial kilns and others gas consuming\n appliances.\n\nFeatures VMR valves are made of aluminum alloy die-cast, with a wide range for inlet/outlet connections\n from DN 10 (3/8”) up to DN 150 (6”).\n\n VMR OTN valves are made of hot-pressed brass with connections from DN8 (1/4”) to DN15 (1/2”).\n Sealings are made of NBR-based rubber certified for use with gas (EN 549).\n Suitable for use with air and non-aggressive gases included in the 1, 2 and 3 families (EN 437).\n Special versions suitable for aggressive gases, free of brass and with FPM seals.\n Pipe connections meet Group 2 and backpressure sealing is compliant with Class A, according\n to EN161 requirements.\n The whole range can be provided in Ex-proof execution, for use in Zones 2 and 22, according to\n 2014/34/EU Directive (ATEX).\n The valve is open only when energized: if, for any reason, power supply goes down, the valve\n closes immediately (intrinsic safe).\n Suitable for heavy-duty cycle operation and qualified for continuous service (100% ED).\n Equipped with flow rate adjustment (except VMR OTN and models 4”-5”-6”).\n An incorporated fine mesh filter protects the valve seat and disc as well as downstream\n components and prevents dirty contamination (except VMR OTN and VMR 60).\n A proof of closure switch or a visual indicator can be installed (see PCS-VI datasheet for details);\n in this case the valve has to be equipped with 1/8” connection on the bottom. Models from 2”½-\n DN65 and above have this features, smaller models can have it on request.\n Provided with 1/4\" pressure test points on two sides in the inlet chamber (except VMR OTN), to\n connect manometers, pressure switches, leakage detectors or other gas equipment. Models from\n 2”½-DN65 and above are provided with pressure test points also in the outlet chamber (on request\n on 1”¼-1”½-2” models).\n The coils are provided with terminal box or with ISO 4400 plug.\n All components are designed to withstand any mechanical, chemical and thermal condition\n occurring during typical service. Effective impregnation and surface treatments have been used\n to improve mechanical sturdiness, sealing and resistance to corrosion of the components.\n Valves are 100% tested by computerized testing machineries and are fully warranted.\n\n\n\n\n 2-11\n\f ELEKTROGAS – Technical Sheet EE161 - 0124\n\n\nFunctioning and\napplication The VMR type valve is a safety shutting device using auxiliary power supply.\n When it is de-energized, the spring pushes on the seal disc, keeping the gas passage closed.\n In the inlet chamber there is the gas line pressure which forces on the disc, increasing the closing\n function and improving the seal.\n When the coil is powered, the valve opens rapidly against the strength of the spring and gas\n pressure. The flow may be adjusted using the regulating screw on the top (see the installation\n and service instructions).\n If the power supply is shut off, the valve rapidly closes, interrupting the gas flow.\n\n\n\n\n Fig.1\n\n\n This kind of valve is normally installed as safety and regulating device in gas trains, for industrial\n applications and gas firing systems.\n Figure 2 shows an example of installation with other Elektrogas devices.\n 1 = Ball valve VSG\n 2 = Filter FG\n 3 = Pressure regulator R\n 4 = Tightness control LD\n 5 = Gas pressure switch PSG\n 6 = Valve position visual indicator VI\n 7 = Fast opening solenoid valve VMR\n 8 = Slow opening solenoid valve VML\n 9 = Tightness control pressure switch\n 10 = Valve position electrical indicator PCS\n 11 = Burner pressure gauge MG\n 12 = Push button valve ME\n\n\n\n\n Fig.2\n\n\n 3-11\n\f ELEKTROGAS – Technical Sheet EE161 - 0124\n\n\nTechnical\nspecifications Tab. 1\n Connections Internal threaded EN 10226-1 from Rp1/4 to Rp2½ or\n ANSI-ASME B1.20 from 1/4”NPT to 2”½NPT\n Flanged ISO 7005 PN16 from DN40 to DN150 or\n ANSI-ASA-ASME B16.5 class 150 from 2” to 6”\n Voltage ratings 230 VAC 50/60 Hz\n 120 VAC 50/60 Hz\n 110 VAC 50/60 Hz\n 24 VAC/DC\n 12 VAC/DC\n Voltage tolerance -15% to +10%\n Ambient temperature -15°C to +60°C (+5°F to +140°F)\n Media temperature\n Max. operating pressure 200 mbar (3 psig)\n 360 mbar (5 psig)\n 500 mbar (7 psig)\n 6 bar * (90 psig)\n Max test pressure 1 bar (15 psig)\n 9 bar * (130 psig)\n Closing time < 1 second\n Opening time < 1 second\n Gas strainer 600 µm (0.02 in)\n (except VMR OTN and VMR 60)\n Enclosure IP54 (NEMA 3)\n optional IP65 with cable (NEMA 4)\n Cable gland M20x1,5 for terminal box\n PG 9 for ISO plug\n Wires cross-section 2,5 mm2 max. (AWG 12) for terminal board\n 1,5 mm2 max. (AWG 14) for ISO plug\n Electrical safety Class I (EN 60335-1)\n Coil winding insulation Class H (200°C, 392°F)\n Coil thermal resistance Class F (155°C, 311°F)\n Materials in contact with gas Aluminum alloy, Brass, Stainless steel, Plated steel\n Anaerobic adhesive, Nitrile rubber (NBR),\n Fluoroelastomer (FPM), Polytetrafluoroethylene (PTFE)\n (*) Operating pressure lower than 200mbar (3psig) not advisable\n Tab. 2\nPower 200 mbar 360 mbar 500 mbar 6 bar\nConsumption (3 psig) (5 psig) (7 psig) (90 psig)\n[W] 230V 120V 110V 24V 12V 230V 120V 110V…