Suntec PUMP B-8800 – Two-stage, two-step pump

[{"filename":"B-8800B_US_Ed3_nov-2024.pdf","text":"SOLENOID TWO STAGE\n TWO STEP PUMP B-8800B\nSUNTEC A-8800B model contains two gear sets and a built-in solenoid which provides a two- B-8800B - US - Ed. 3 - November 2024\nmode pressure operation. The first stage gear set sucks the fuel from the line, and the second\nstage gear set pressurizes the fuel. This unit is supplied for 1-pipe operation, without by-pass PUMP\nplug installed. Please verify before installation. IDENTIFICATION\nCOMPATIBILITY Two stages\n- Fuel oil #2 and lighter, B6-B100 (blends from 6% up to 100% biodiesel, per ASTM D396).\n Rated motor seed :\nPUMP OPERATING PRINCIPLE 1 : 1725 rpm\n 2 : 3450 rpm\nAs the motor starts, the fuel from the second stage gearset is transferred to the pressure\nregulating valve. Strainer : See technical data\nThe high pressure mode is obtained with the solenoid valve activated (ie. closed); activating\nthis solenoid valve closes the by-pass channel to the return. Oil is then transferred to the nozzle Shaft rotation\nline at the pressure given by the high pressure regulating valve. and nozzle location\n (seen from shaft end) :\nThe low pressure mode is obtained with the solenoid valve open (ie. non activated); the by- A :clockwise rotation/\npass channel is open, the oil is supplied to the nozzle line via the by-pass hole and the low right hand nozzle. (RH-RH)\npressure adjustment is made by the screw on the solenoid tube. C : anti clockwise rotation/\nIt is preferable to set the high pressure given by the pump valve (with solenoid activated) before left hand nozzle.(LH-LH)\nthe low pressure, with solenoid non activated. Care should be taken not to overtighten the low\npressure adjusting screw of the solenoid tube, as this may eliminate the low pressure range.\nOne pipe installation B 2 T A 8850 B 8\nThe by-pass plug must not be installed. The excess fuel is returned back to the inlet.\nTwo pipe installation\nThe steel plug of the return port must be removed and the by-pass plug must be inserted in Identification number\nthe return port allowing excess fuel is bypassed back to the tank. The return plug must not be\nreinstalled. B : B6-B100 applications\nBleed Revision\nIn one pipe operation, the easy flow bleeder valve must be loosened to bleed the system. Bleeding\nin two pipe operation is automatic, but it may be accelerated by loosening the easy flow bleeder.\nNote\nOwing to the presence of the nozzle by-pass hole, the pump has no cut-off function; cut-off\nmust be provided by an external solenoid valve.\n\n\n\n\n Solenoid valve open Solenoid valve closed\n (low pressure mode) Low pressure (high pressure mode)\n adjustment\n\n\n By-pass\n channel\n\n High pressure\n adjustment\n To nozzle\n\n By-pass Shaft seal\n hole\n Pressure\n gauge port\n Back to suction\n Gear set\n\n Oil under suction\n\n Oil under pressure By-pass By-pass\n plug plug Vacuum\n removed inserted gauge port\n By-passed oil\n Return\n returned to tank\n plugged\n or to suction Return Suction\n ONE PIPE TWO PIPE\n INSTALLATION INSTALLATION\n\n\n\n Suntec Industries Incorporated - 60 Aberdeen Drive - Glasgow, KY 42141 - USA\n Tel : 270 651 7116 - www.suntecpumps.com\n\f TECHNICAL DATA\n\n General\n\n Mounting Flange mounting Strainer open area T = min 10,5 in2\n Certified\n Connection threads\n B6-B100: US only\n Inlet 1/4 NPTF\n Nozzle outlet 1/8 NPTF\n Pressure gauge port 1/8 NPSF\n Bleeder valve port 1/8 NPSF\n Hydraulic data\n Valve function Pressure regulation and cut-off\n Oil temperature 32 - 140°F\n Cut-off Motor speed dependent Ambiant temperature 32 - 140°F\n Inlet and return pressures 10 psi max.\n Shaft 5/16 in\n NFPA limits pressures to 3 psi max\n\n By-pass plug Not inserted in return port, for Suction height Single pipe: 6\" Hg max. vacuum,\n one pipe system. To be inserted in Two-pipe: 17\" Hg max. vacuum, to\n return port with a 5/32 Allen key for prevent air separation from oil\n two-pipe system\n\n\n\n Nozzle rating\n Model number Nozzle rating Power consumption at 300 PSI\n B2TA-8850B 10 GPH at 300 PSI 250W\n B2TA-8851B 16 GPH at 300 PSI 285W\n B2TA-8852B 23 GPH at 300 PSI 330W\n\n\n Solenoid valve characteristics\n\n Frenquency 50/60 Hz Solenoid coil number system\n N 6 2 1 L\n CORDSET TYPE R - R.H LEADS\n Consumption 9W N - NON DELAY L - L.H LEADS\n X - NO CORDSET (From shaft end)\n Maximum pressure 300 psi COIL VOLTAGE LEADS LENGHTS\n 2 - 12 VDC/24 VAC X1 - NO CORDSET\n 6 - 115 VAC 21 - 13 INCH (PARTIAL JACKET)\n 7 - 220 VAC 42, 53, 61 - 22.5 INCH (NO JACKET)\n\n\n\nPUMP DIMENSIONS (in inches)\n\n Two-pipe system\n (by-pass plug inserted\n in return port)\n\n\n\n\n  \n \n\n\n\n\n  \n  \n \n\n\n\n  Inlet  Return  Nozzle outlet  Pressure gauge port  Pressure  Bleeder valve  Internal by-pass plug\n adjustment\n\n We reserve the right to change specifications without prior notice.…