Fireye 69ND1 Ionization Flame Rod

[{"filename":"SC-103-Flame_Scanner_48PT2_Flame_Rod_69ND1_English_2018-06-07.pdf","text":"®\n\n SC-103\n JUNE 7, 2018\n\n\n ®\n FIREYE\n 48PT1\n (Obsolete)\n FLAME SCANNERS\n INFRARED: 48PT1, 48PT2 and 48PT2-CEX\n FLAME ROD: 3G-OTH-02791\n 48PT2 For UV Self-Check Scanners use SC-101\n For Hazardous Locations or NEMA 4X Scanners use SC-106\n For Non Self-Check UV Scanners use SC-102\n\n 3G-OTH-02791\n\n APPROVED\n\n\n\n\nDESCRIPTION\n The 48PT2 scanner comes with cables rated for Tray Cable - Exposed Run (TC-ER) and complies\n with the crush and impact requirements of the standard for metal clad cable, UL 1569.\n 48PT1 (Obsolete)\n The 48PT1 lead sulfide infrared scanner contains a high impedance detector and is designed to be\n used only on P-Series controls.\n\n 48PT2\n The 48PT2 lead sulfide infrared scanner contains a low impedance detector and is designed to detect\n low flicker frequency IR signals from gas and oil flames. It is designed for use on D-Series, Flame-\n Monitor, FlameWorx, MicroM and Burnerlogix controls.\n\n 48PT2-CEX\n The 48PT2-CEX is a 48PT2 mounted in a ATEX compliant housing for environments requiring the\n rating of Exd IIC T6 ATEX hazardous location.\n\n 3G-OTH-02791\n The 3G-OTH-02791 flame rod is made of high temperature resistant metal and can be used only to detect gas\n flames. The rods come in 12, 18 and 24 inch lengths.\n\n\n CAUTION: Fireye scanners are for use only with Fireye controls. Do not connect Fireye\n scanners with controls not manufactured by FIREYE.\n\n CAUTION: If component checking is required during burner operation for constantly fired\n burners, utilize the infrared flame scanner (48PT2) with associated AutoCheck amplifier. For\n Flame-Monitor systems use the E1R1, E1R3 or E1R2 and for MicroM systems use the MEIR1\n or MEIR4.\n Warning- all installation, service and troubleshooting of Fireye products must be performed\n by a qualified technician.\n\n\n 1\n\f \n\n\n\n\n 13/16 HEX 2 3/8\n 5.0 (127) (20.6) (60.3) ”L”\n 2.504 1” DIA. 2 1/2 2 3/8\n (63.6) (25.4) (63.5) (60.3)\n 15/16 HEX\n (23.8) 1/2\n (12.7)\n 1 1/4 DIA.\n (31.8)\n\n\n.385 DIA. (8.7) HEAT INSULATOR\n 1/2-14 1/2-14 NPT\nTC-ER CABLE\n 1/2-14 TAPERED ”L” LENGTH AS SPECIFIED: 12”, 18”, 24” (304.8, 457.2, 609.6)\n STRAIGHT PIPE THD PIPE THD\n\n\n 48PT2-1000 SERIES INFRARED SCANNER 3G-OTH-02791 FLAME ROD\n\n\n\n 3.96 (100.5)\n 1.02” 2 1/2\n 1.46 DIA. (63.5)\n (37.1) 13/32 (10)\n\n\n 1 1/4 DIA.\n (31.8)\n 2.13\n (54)\n HEAT INSULATOR\n 1/2-14\n 1/2-1 TAPERED\n STRAIGHT PIPE THD PIPE THD\n\n .385 DIA. (8.7) TC-ER CABLE\n\n\n 48PT2-9000 SERIES INFRARED SCANNER\n\n\n\n Scanner Model Type Approx. Volts Approx. Resistance* Ambient Temp. Limits\n Across Cell of Cell\n 48PT1 Infrared 125VDC 1.5 Meg. ohms 140°F/ 60°C, -40°\n 48PT2 Infrared 7-15VDC 20K - 80K ohms 140°F / 60°C, -40°\n 48PT2-CEX\n 3G-OTH-02791 Flame Rod 280-305 VAC Infinite Tip 2460°F\n 1500°F/816°C, -40°\n * Resistance measured with 20K Ohms/ Volt Meter\n For proper Flame Signal Voltage see technical bulletin for the appropriate control.\n 48PT2 scanners comply with NEMA 4X\n\n PART NUMBER DESCRIPTION USE WITH\n 48PT1-1003 IR Straight Head 8 feet (2440mm) leads\n 48PT1-1007 IR Straight Head 4 feet (1220mm) Leads\n 48PT1-9003 IR 90 deg. Head 8 ft. (2440mm) Leads P-Series\n 48PT1-9007 IR 90 deg. Head 4 ft. (1220mm) Leads\n 48PT1-9007W - 9007 Water Repellent\n 48PT2-1003 IR Straight Head 8 feet (2440mm) leads\n 48PT2-1007 IR Straight Head 4 feet (1220mm) Leads C & D Series, MicroM,\n 48PT2-9003 IR 90 deg. Head 8 ft. (2440mm) Leads FLAME-MONITOR,\n 48PT2-9007 IR 90 deg. Head 4 ft. (1220mm) Leads BurnerLogix\n 48PT2-CEX IR Straight Head, 1/2” NPT inlet\n 35-69 Heat Insulator for 48PT Scanners\n 3G-OTH-02791-1000K4 Flame Rod 12 inches (305mm) 1/2 in. mount\n P, C, D, M-Series, MicroM,\n 3G-OTH-02791-1000K6 Flame Rod 18 inch (460mm) 1/2 in. mount)\n MB Systems, BurnerLogix,\n 3G-OTH-02791-1000K8 Flame Rod 24 inches (710mm) 1/2 in. mount\n FLAME-MONITOR\n\n For information on the 45UV scanners, see Bulletin SC-101.\n For information on the 55UV scanners, see Bulletin SC-106.\n For information on the UV1A, UV2, and UV8A scanners, see Bulletin SC-102.\n\n\n2\n\f ®\n\n\n\n\nSCANNER MAINTENANCE\n 48PT1 and 48PT2, 48PT2-CEX Infrared Scanners and 3G-OTH-02791 Flame Rods\n The viewing area of the scanner must be kept clean. Even a small amount of contamination will\n reduce the flame signal reaching the detector by a measurable amount. Wipe the viewing area rou-\n tinely using a soft cloth dampened with concentrated detergent.\n Type 48PT1 scanner includes a replaceable #4-128-1 cell\n Type 48PT2, 48PT2-CEX scanner includes a replaceable #4-263-1 Firetron cell.\n Type 3G-OTH-02791 Flame Rod. Rods should be routinely replaced as they…